|
Laser Marker
for Capacitors on line
--ZS—CO210-16
This
system is made up of ZS-CO210
High-Speed Vibrating Mirror Laser Marking System and Automatic feeder
for the knitted capacitances. The knitted capacitances run through the
first buffer, and then with the leading of electrical machine, they are
sent to the position, which is under the scanner. It is flying marking
and the marking speed is 200-300 per |
(Click to see big
picture) |
|
|
minute. The next step is that the marked capacitances are sent to the
test machine with the help of the second buffer. Marking and testing the
capacitance happens at the same time, and their speed is the same too.
It is just to say this marking system works continually. The buffers of
this marking system still enjoys several responsive instruments, which
make the marking system stop to be fixed when there is something wrong
with it. And this marking system is specially designed for marking on
knitted capacitances. The marked sign admitted by several countries or
model is very clear and the marking speed is very quick too.
Main Technical Specifications：
1、Laser
Power：10
W；Laser
wavelength：10.6μm；
2、Laser
life：≥45000/hour(aeration
after 10000hours)
3、Scanning
Speed：7000mm/second
；Marking
Speed：4—8pcs/s
4、Marking
scope：50mm×50mm。
5、Min.
character：0.4mmhigh；Min.
line width：0.08mm；
6、Marking
position accuracy：±0.1mm.
7、Power
input：220V/1.5kw
8、24-hour
continuous operation without stop
9、Volume：1900mm×860mm×1500mm
Main Configurations：
1、Host：ZS-CO210
High-Speed Vibrating Mirror Laser Marking System
2、Automatic
feeding system：guide
of feeding system、Feeding
synchronous rotation Group
。
3、Drive
System
：drive
device for back and front
4、Reserve
System
：buffer、Reserve
System of back and front
5、Purification
System
：dust
absorption device (Suction mouth is reserved)
6、Control
system：Photoelectric
detection system, microcomputer control system
The Installing Environment for CO2
series of Laser Marking Systems:
一.
Power supply requests:
Power source:
220V±10% (single-phase), has independent electric wire
to meet the ground
Frequency: 50Hz
Electric current: 10A
二.
Working conditions:
Ambient temperature: 5 ~ 30℃
Relative humidity: <= 75% (no congeal)
The system should be placed on the space
environment : clean, relatively no dust, no strong vibration body
around ,without heat, ventilation, clean and bright, to ensure good
ventilation, the system and the distance between the walls and other
obstructions to maintain at least 0.6m
Electromagnetic environment:
without strong
electronmagetic interference, and the computer can work normally.
☆Watch
out:
Protect your
body (especially your eyes) to avoid damage from the direct
Illumination
of laser .
☆Read
the product instructions first and carry on the operation according to
the request strictly!
☆If
the abnormal phenomenon appears, close the master switch first and then
inspect.
☆Attention
to the process of using the equipment such as a sudden power outages, we
should close down all the switches. After that we should use it
according to the normal sequence, otherwise this will cause great damage
to equipment.
☆Keep
the room and the surface of machine neat.
☆The
working place should be equipped with cleaning and ventilation pipes to
remove the dust and exhaust produced in the process.
☆After
localization, we should adjust the earthquake-prevented foot pads
according to the state of ground to make the floor of the equipment and
the ground contact steadily and assume the horizontal shape.
☆The
laymen are not allowed to overhaul when the machine is opened in order
to avoid electric shock accident because the electric circuit presents
high-pressured condition when the system works.
[Return] |