|
Automatic Laser Marker
for Pipe Components
--ZS-CO210-23
This system is made up of ZS-CO210 High-Speed Vibrating Mirror
Laser Marker and automatic Pipe Components Feeding system, which
integrates the processes of automatic feeding, laser marking, electric
brush dust, automatic stuffing into tubes ,and automatic unloading
storage pipe. It is specially designed for TO—220,TO—126, TO—251.This
|
(Click to see big
picture) |
|
|
system has 4 storage hopper, each of which can store 30 Material Pipe.
Manipulator control will be used to feed up to the place, rotating
cylinder will be used to maximum effect was observed at 40 ° tube
rotation state components with track down hard spaces, a group of five
components; compact laser marking machine made in accordance with the
directives of various computer.This system with features of small size,
reliability, high quality, if specially fit for enterprises who produce
high-grade pipe components.
Features：High
efficient, low energy consumption, the entire process to avoid touch
processing components, the effective protection element is not
contaminated.
Main Technical Specifications：
1、Laser
power：10
W；Laser
wavelength：10.6μm；
2、Laser
life：≥45000hours(aeration
after10000hours)
3、Scanning
speed：7000mm/second
4、Marking
speed：2-4pcs/s(Marking
speed is inversely proportional to marking content)；
5、Marking
scope：50mm×50mm；
6、Min.
Character
：0.8mmhigh；Min.
line width：0.08mm；
7、Marking
position accuracy：±0.1mm；
8、Force:
Power input:220V/0.7kw; Gas input：0.4-0.7MP；
9、Continuous
working time: 24 hours uninterrupted movements；
10、Volume：1300mm×850mm×1250mm。
Main Configurations：
1、Host：
ZS-CO210 High-Speed
Vibrating Mirror Laser Marking System.
2、Automatic
feeding system：feeding、Pipe
moving parts Discharger, equipment control, discharge control devices.
3、Storage
System：4
storage Hopper；
4、Electric
bushing dust：Electric brushing devices (dust suction mouth is
reserved);
5、Control
system：Photoelectric
detection system; Pneumatic systems;Microcomputer control system; Marking
software systems.
The Installing Environment for CO2
series of Laser Marking Systems:
一.
Power supply requests:
Power source:
220V±10% (single-phase), has independent electric wire
to meet the ground
Frequency: 50Hz
Electric current: 10A
二.
Working conditions:
Ambient temperature: 5 ~ 30℃
Relative humidity: <= 75% (no congeal)
The system should be placed on the space
environment : clean, relatively no dust, no strong vibration body
around ,without heat, ventilation, clean and bright, to ensure good
ventilation, the system and the distance between the walls and other
obstructions to maintain at least 0.6m
Electromagnetic environment:
without strong
electronmagetic interference, and the computer can work normally.
☆Watch
out:
Protect your
body (especially your eyes) to avoid damage from the direct
Illumination
of laser .
☆Read
the product instructions first and carry on the operation according to
the request strictly!
☆If
the abnormal phenomenon appears, close the master switch first and then
inspect.
☆Attention
to the process of using the equipment such as a sudden power outages, we
should close down all the switches. After that we should use it
according to the normal sequence, otherwise this will cause great damage
to equipment.
☆Keep
the room and the surface of machine neat.
☆The
working place should be equipped with cleaning and ventilation pipes to
remove the dust and exhaust produced in the process.
☆After
localization, we should adjust the earthquake-prevented foot pads
according to the state of ground to make the floor of the equipment and
the ground contact steadily and assume the horizontal shape.
☆The
laymen are not allowed to overhaul when the machine is opened in order
to avoid electric shock accident because the electric circuit presents
high-pressured condition when the system works.
[Return] |